[Q92-Q114] Ultimate Guide to Prepare CWDP-305 with Accurate PDF Questions [Oct 03, 2025]

QUESTION 92
During a validation site survey, you realize that the installers mounted some of the APs above the ceiling. They said that this was a request from the building architect due to aesthetics constraints.
During the requirements gathering, you weren’t advised about any aesthetics constraints from the main stakeholder of the project. What should you do in this case?
Response:

QUESTION 93
You are conducting a physical site survey where heavy machinery is repaired. What is a common item required specifically for this type of survey?

QUESTION 94
A table of VLANs in a _________ document should include what device performs ________ services.(Fill in the blanks)

QUESTION 95
A customer wants to deploy a WLAN that employs centralized forwarding. What LAN requirements should you look for?

QUESTION 96
A controller-based WLAN infrastructure has its controller on a different subnet than its APs. What device must be used to enable any communication between the Controller and the APs?

QUESTION 97
SSID hiding is not generally recommended because some frames require inclusion of the SSID. In what frames is the SSID always included?
Response:

QUESTION 98
One of your customers plans on providing wireless coverage to a warehouse facility. After performing an initial walkthrough, you collect the following information:
The central part of the warehouse is between 400 and 600 feet (122 to 183 meters) from the warehouse switches mounted on the walls.
The warehouse storage is composed of metallic racks with varying inventory levels and contents, from electronics and plastic toys to food pallets and juice bottles.
Workers need basic data coverage from their working location and are not highly mobile. They usually work from one single aisle, and their laptop is on a cart with wheels.
What would be your one recommendation to provide coverage to the central area of the warehouse?

QUESTION 99
What action should be taken after implementing a WLAN based on the design developed from the site survey process?

QUESTION 100
You are being asked to design a WLAN for a number of WLAN clients that will use Telnet as the primary application. The customer has asked that you use only the number of APs necessary because of the complex installation and construction costs each AP installation will incur in this particular environment.
What design factors do you consider?
Response:

QUESTION 101
What is the most appropriate antenna which will require the least Intentional Radiator power for a point-to- point bridge link spanning 1200 meters?

QUESTION 102
Why should band steering algorithms allow stations to connect to the 2.4 GHz band after some number of ignored Probe Requests?

QUESTION 103
ABC Company has a WLAN controller with 10 controller-based APs; the Voice SSID is configured for centralized data forwarding. Each AP is connected to an access port on a layer-2 Ethernet switch. Each layer-
2 switch is uplinked to a single layer-3 core Ethernet switch. The WLAN controller is connected directly to the layer-3 core Ethernet switch. Layer-3 tunnels are created between all controller-based APs and the WLAN controller. A voice server is connected to the layer-3 Ethernet switch.
When a voice-enabled QoS STA sends an IP data packet to a voice server in this scenario, the DSCP value carried in the STA’s IP data packet gets mapped to what and by which device?

QUESTION 104
While configuring your site survey software for an upcoming manual survey project, you notice the configuration option for “Network Card Simulation”. What is the purpose of such a feature and when would you use it?

QUESTION 105
When deploying access points (APs) outdoors, which additional component needs to be used that is typically not required in most indoor office deployments?

QUESTION 106
When deploying a new WLAN infrastructure using PoE to power the APs, you realize that a known good AP is not powering up. You use the same cable to connect your laptop and connect without any trouble. What is the most likely reason the AP did not power up?

QUESTION 107
While using a USB adapter attached to a USB hub and your laptop for protocol analysts you notice that the SNR is lower than expected. The USB adapter is an 802 11 ac 3×3 3 adapter and is connected to a USB 3 hub.
What is likely causing the SNR variation?

QUESTION 108
In a convention center, you have received complaints about the WLAN infrastructure. At this moment, there are only two APs in one auditorium. After analyzing the situation, you determined that there are more client devices than the infrastructure was designed for. There are only two APs to support more than 300 devices using the Wi-Fi at the same time. What should you do to make the Wi-Fi work as expected?

QUESTION 109
Which document provided to your customer should include all devices and parts that will be used during the deployment of their WLAN infrastructure?

QUESTION 110
When designing a wireless bridge to connect two offices 13 kilometers (approximately 8 miles) apart, which factor must the Wireless Engineer consider to account for Fresnel Zone clearance?

QUESTION 111
As a device starts to shift to lower PHY rates, what factors usually influence a device decision to shift to lower PHY rates?(Choose all that apply.)

QUESTION 112
While conducting a site survey in a heavy machinery repair facility, what essential gear should you use for safety in this challenging environment?

QUESTION 113
Which advantage provided by 802.11n and 802.11ac is not usable in 1×1:1 low-end client devices?

QUESTION 114
What differences exist between VLANs in wireless and wired domains?